Mubychem Group, established in 1976, is the pioneer manufacturer of Calcium Chloride, Pharmaceutical, Fragrance & Flavor chemicals in India. Mubychem Group has several manufacturing facilities spread across Gujarat and Mumbai India and world wide contacts and toll manufacturers. We are exporting globally to countries like USA, Europe, UAE, South Africa, Tanzania, Kenya, Egypt, Nigeria, Uganda, Turkey, Mexico, Brazil, Chile, Argentina, Dubai, Indonesia, Spain etc. |
|
The participating units have one or more accreditations like FDA - GMP approval; ISO-9001 Certified; "REACH" Pre-registered; ISO-22000; Kosher Certified; Halal Certified; HACCP. We offer Pure & IP BP USP FCC Food Grade ACS AR Analytical Reagent Grades of Chemicals |
|
--------
--------
Calcium Chloride BP Ph Eur USP IP AR Analytical Reagent FCC Food grade Manufacturers
Calcium Chloride BP USP ACS Analytical Reagent Food Grade Manufacturers
For MSDS Sheet Click
CaCl2 Anhydrous MSDS Sheet
CaCl2 Fused Dihydrate MSDS Sheet
CaCl2 Hexahydrate Solution MSDS Sheet
Calcium Chloride
Dihydrate
Powder, Crystals, Dihydrate, Hexahydrate,
Desiccant Tablets, Pellets.
CAS Number 10035-04-8, 7774-34-7 and 10043-52-4, BP Ph. Eur. USP ACS AR LR FCC Food Grades
Calcium Chloride USP Grade Specifications
Calcium Chloride,
Dihydrate. USP
CaCl2·2H2O -- 147.01
Assay— Calcium
Chloride contains an amount of CaCl2 equivalent to not less than 99.0
percent and not more than 107.0 percent of CaCl2·2H2O.
Packaging and storage— Preserve in tight containers.
Labeling— Where
Calcium Chloride is intended for use in hem dialysis, it is so labeled.
Identification— A
solution (1 in 10) responds to the tests for Calcium and for Chloride.
pH: between 4.5 and
9.2, in a solution (1 in 20).
Aluminum (where it
is labeled as intended for use in hem dialysis)— the limit is 1 4g per g.
Iron, aluminum, and
phosphate— To a solution (1 in 20) add 2 drops of 3 N hydrochloric acid
and 1 drop of phenolphthalein TS. Then add ammonium chloride–ammonium
hydroxide TS, drop wise, until the solution is faintly pink, add 2 drops in
excess, and heat the liquid to boiling: no turbidity or precipitate is
produced.
Heavy metals— the
limit is 0.001%.
Limit of magnesium and
alkali salts— Dissolve 1 g in about 50 mL of water, add 500 mg of
ammonium chloride, and proceed as directed in the test for Limit of
magnesium and alkali salts under Calcium Carbonate, beginning
with “heat the solution, and boil for 1 minute”: the weight of the residue
does not exceed 5 mg (1.0%).
Organic volatile
impurities meets the requirements.
Calcium Chloride BP Ph Eur Dihydrate Grade Specifications
Calcium Chloride BP
Dihydrate
CaCl2-2H2O
DEFINITION
Content
97.0 per cent to 103.0 per cent of CaCl2,2H2O.
CHARACTERS
Appearance
White or almost white, crystalline powder, hygroscopic.
Solubility
Freely soluble in water, soluble in ethanol (96 per cent).
IDENTIFICATION
Solution S (see Tests) gives reaction
of chlorides.
It gives the reactions of calcium.
It complies with the limits of the
assay.
TESTS
Solution S
Dissolve 10.0 g in carbon dioxide-free water
prepared from distilled water and dilute to 100 ml with the same solvent.
Appearance of solution: Solution S is clear and not more intensely coloured than reference
solution.
Acidity or alkalinity: To 10 ml of freshly prepared solution S add 0.1 ml of
phenolphthalein
solution. If the solution is red, not more than 0.2 ml of 0.01 M hydrochloric acid
is
required to discharge the colour and if the solution is colourless, not more
than 0.2 ml of 0.01 M sodium hydroxide is required to turn it red.
Sulphates: Maximum 300 ppm.
Aluminium: To 10 ml of solution S add 2 ml of ammonium chloride solution R
and 1
ml of dilute ammonia and boil the solution. No turbidity or
precipitate is formed.
If intended for use in the manufacture of dialysis solutions, the above test
is replaced by the test for aluminium maximum 1 ppm.
Barium: To 10 ml of solution S add 1 ml of calcium sulphate solution R .
After at least 15 min, any opalescence in the solution is not more intense
than that in a mixture of 1 ml of distilled water and 10 ml of
solution S.
Iron: Maximum 10 ppm, determined on solution S.
Magnesium and alkali metals: Maximum 0.5 per cent.
Heavy metals: Maximum 20 ppm.
Calcium Chloride Hexahydrate BP Ph Eur Grade Specifications
Calcium Chloride BP Hexahydrate
CaCl2,6H2O
DEFINITION
Content
97.0 per cent to 103.0 per cent of CaCl2,6H2O.
CHARACTERS
Appearance
White or almost white, crystalline mass or colourless crystals.
Solubility
Very soluble in water, freely soluble in ethanol (96 per cent).
It solidifies at about 29C.
IDENTIFICATION
Solution S (see Tests) gives reaction
of chlorides.
It gives the reactions of calcium.
It complies with the limits of the
assay.
TESTS
Solution S
Dissolve 15.0 g in carbon dioxide-free water
prepared from distilled water R and dilute to 100 ml with the same solvent.
Appearance of solution: Solution S is clear and not more intensely coloured than reference solution.
Acidity or alkalinity: To 10 ml of freshly prepared solution S add 0.1 ml of
phenolphthalein
solution. If the solution is red, not more than 0.2 ml of 0.01 M
hydrochloric acid is required to discharge the colour and if the
solution is colourless, not more than 0.2 ml of 0.01 M sodium hydroxide
is required to turn it red.
Sulphates: Maximum 200 ppm.
Aluminium: To 10 ml of solution S add 2 ml of ammonium chloride solution R
and 1
ml of dilute ammonia R1 . Heat to boiling. No turbidity or precipitate
is formed. If intended for use in the manufacture of dialysis solutions, the
above test is replaced by the test for aluminium : maximum 1 ppm.
Barium: To 10 ml of solution S add 1 ml of calcium sulphate solution. After
at least 15 min, any opalescence in the solution is not more intense than
that in a mixture of 1 ml of distilled water and 10 ml of solution
S.
Iron: Maximum 7 ppm, determined on solution S.
Magnesium and alkali metals: Maximum 0.3 per cent.
Heavy metals Maximum 15 ppm.
Calcium Chloride Injection as per USP Grade Specifications
Calcium Chloride
Calcium Chloride Injection is a sterile solution of Calcium Chloride in Water for Injection. It contains not less than 95.0 percent and not more than 105.0 percent of the labeled amount of CaCl2·2H2O.
Packaging and storage— Preserve in single-dose containers, preferably of Type I glass.
Identification— It
responds to the tests for Calcium and Chloride.
Bacterial
end toxins— It contains not more than 0.2 USP End toxin Unit per mg of calcium
chloride.
pH: between 5.5 and
7.5 in the undiluted Injection, except where the concentration is greater
than 1 in 20, in which case this range applies to the Injection diluted with
water to yield a concentration of 1 in 20.
Particulate matter:
meets the requirements for small-volume injections.
Other requirements—
It meets the requirements under Injections 1.
Calcium Chloride FCC Food Grade Specifications
CaCl2 Formula weight,
anhydrous 110.98
CaCl2·2H2O Formula wt,
dihydrate 147.01
Calcium Chloride
DESCRIPTION
Calcium Chloride occurs as
white, hard fragments, granules, or powder. It is anhydrous or contains two
molecules of water of hydration. It is deliquescent. It is soluble in water
and slightly soluble in
alcohol. The pH of a 1:20 aqueous solution is between 4.5 and 11.0.
Function Firming
agent.
REQUIREMENTS
Labeling: Indicate whether it is anhydrous or the
dihydrate.
Identification: A
1:10 aqueous solution gives positive tests for Calcium and for Chloride.
Assay: Anhydrous:
Not less than 93.0% and not more than 100.5% of CaCl2; Dihydrate: Not
less than 99.0% and not more than 107.0% of CaCl2·2H2O.
Acid-Insoluble Matter Anhydrous: Not more than 0.02%; no particles per kilogram of
sample greater than 2 mm in any dimension.
Arsenic: Not more
than 3 mg/kg.
Fluoride: Not more
than 0.004%.
Lead: Not more than
5 mg/kg.
Magnesium and Alkali
Salts Anhydrous: Not more than 5.0%; Dihydrate: Not more
than 4.0%.
Calcium Chloride Solution FCC Food Grade Specifications
Calcium Chloride
DESCRIPTION
Calcium Chloride Solution
occurs as a clear to slightly turbid, colorless or slightly colored liquid
at room temperature. It is normally available in a concentration range of
about 35% to 45% of CaCl2.
Function: Sequestrant; firming agent.
REQUIREMENTS
Identification: When
diluted to a concentration of about 1:10 (CaCl2 basis), a sample gives
positive tests for Calcium and for Chloride.
Assay: Not less than
90.0% and not more than 110.0%, by weight, of the labeled amount of calcium
chloride, expressed as CaCl2.
Alkalinity [as
Ca(OH)2]: Not more than 0.3%.
Fluoride: Not more
than 0.004%, calculated on the amount of CaCl2 as determined in the Assay.
Lead: Not more than
4 mg/kg, calculated on the amount of CaCl2 as determined in the Assay.
Magnesium and Alkali
Salts: Not more than 5.0%, calculated on the amount of Calcium
Chloride as
determined in the Assay.
Calcium Chloride Dihydrate ACS Reagent Grade Specifications, Calcium Chloride ACS
CaCl2-2H2O
Formula Weight 147.01
CAS Number 10035-04-8
Calcium Chloride
REQUIREMENTS
Assay: 99.0-105.0% CaCl2 - 2H2O
pH of a 5% solution: 4.5-8.5 at 25C
MAXIMUM ALLOWABLE
Insoluble matter: 0.01%
Oxidizing substances
(as NO3): 0.003%
Sulfate (SO4): 0.01%
Ammonium (NH4): 0.005%
Barium (Ba): 0.005%
Heavy metals (as Pb): 5 ppm
Iron (Fe): 0.001%
Magnesium (Mg): 0.005%
Potassium (K): 0.01%
Sodium (Na): 0.02%
Strontium (Sr): 0.1%
Calcium Chloride Desiccant
CaCl2
Formula Wt 110.98
CAS Number 10043-52-4
REQUIREMENTS
Assay: 96.0%
CaCl2
MAXIMUM ALLOWABLE
Titrable base: 0.006 meq/g
Calcium Chloride BP USP IP FCC Foode grade ACS Analytical Reagent Manufacturers:
MUBYCHEM GROUP
CHINCHBUNDER, MUMBAI 400009, INDIA
TEL: (OFFICE)
91-22-23774610, 91-22- 23723564. 91-22-23728264
e-mail: info@mubychem.com
USA & Canadian Customers may e-mail: us@mubychem.com
Copyright
and Usual
Disclaimer
is Applicable.
Global or International Calcium Chloride Anhydrous Fused Dihydrate BP USP IP FCC ACS Food Grade ... Suppliers, Exporters, Importers, Manufacturers
If I give you “My Word” Nobody can undo it.
If I sign an “Agreement” my Lawyer will undo it
Perfection is made up of small thing but it is not small.
29-Apr-2022